BLOG

MY PERSONAL JOURNEY

HT12D DATASHEET IN PDF

HT12D 2 12 Series of Decoders Features. Operating voltage: V~12V Low power and high noise immunity CMOS Built-in oscillator needs only 5% resistor. IC HT12D can be used only with its pair HT12E. These two ICs together form an Encoder and Decoder pair. They are bit. HT12D Datasheet, HT12D Holtek Decoder Datasheet, buy HT12D Decoder IC.

Author: Malagami Vozragore
Country: Saint Kitts and Nevis
Language: English (Spanish)
Genre: Art
Published (Last): 19 May 2005
Pages: 493
PDF File Size: 14.8 Mb
ePub File Size: 13.1 Mb
ISBN: 851-4-82942-586-9
Downloads: 51937
Price: Free* [*Free Regsitration Required]
Uploader: Nejinn

Supply voltage; 5V 2.

They are paired with 2 12 series of encoders. Valid transmission; active high.

This pin powers the IC should use only 5V. Submitted by admin on 27 October What is Web Browser.

In the above circuit I have set the 8-bit address data as 0b, by connecting all address pins to ground. In simple terms, HT12D converts the serial input into parallel outputs. A valid transmission in indicated by a high signal at VT pin.

Choosing Battery for Robots. It is very important that your Decoder should have the same address of that of the encoder. Interface GPS with Arduino. Connected to the I of circuit. If any valid data is received they can be obtained from these four pins. Interface SD Card with Arduino. They can also be datqsheet to LED to physically view the received data.

This series of decoders are hy12d used for remote control system applications, like burglar alarm, car door controller, security system etc. Virgin Galactic — Commercial Space Flight. The serial input data is compared with the local addresses three times continuously.

  LUVITOL LITE PDF

HT12D is a decoder integrated circuit that belongs to 2 12 series of decoders. We should set the bits in same pattern on Encoder and Decoder IC to pair them.

It is mainly provided to interface RF and infrared circuits. These two ICs together form an Encoder and Decoder pair.

To know how a 4-bit data can be encoded and then send to the input pin of this IC, we have to understand the working of the HT12E Encoder IC which is given here. The input data code is decoded when no error or unmatched codes datawheet found.

HT12D is capable of decoding 12 bits, of which 8 are address bits and 4 are data bits. Can be used in Home automation for short range remote switching Safety systems like Burglar alarm system, Smoke or Fire alarm system etc.

HT12D RF Decoder IC Pinout, Details, Equivalent & Datasheet

The data on 4 bit latch type output pins remain unchanged until new is received. TL — Programmable Reference Voltage. So if you are working on a project which has to transmit a 4-bit data from one end to other either by wire or wireless then this IC pair will be best suited for you. SPI Module of Arduino. This oscillator can be used by connecting these two pins through a 1M Resistor.

The Encoded 12 bit output data obtained from HT12E has to be given here. This oscillator can be used by connecting these two pins through a 1M Resistor 17 Valid Transmission VT This pin will un high when a data is ht12.

  BEHIND THE KITCHEN DOOR SARU JAYARAMAN PDF

For decoding a data the IC will requires an oscillatorluckily this IC has one in-built. These are the 8-bit address bits, which is used to protect your data. A basic circuit diagram for the HT12D IC is shown below In the above circuit I have set the 8-bit address data as 0b, by connecting all address pins to ground.

The IC is should be powered by 5V pin 18 and the ground pin pin 9 is grounded. Arduino based GPS receiver. Choosing Motor For Robots. This pin will go high when a data is received. Skip to main content.

This high-density System-in-Package SiP integrates controller, power switches, and support components. It decodes the serial addresses and data received by, say, an RF receiver, into parallel data and sends them to ni data pins. So out of the bits 8-bits will be used to set address and the remaining 4-bit will be used to transmit data.

HT12D Decoder IC

If you want security you can connect any of the 8 pins to 5V to make it high. The IC has a built in oscillator. The 4-bit data that is received can be obtained on pins AD0 to AD1 and an address of 8-bit has to be set using daasheet pins A0 to A7.

It is not mandatory to use it.