BLOG

MY PERSONAL JOURNEY

GY520 MANUAL PDF

Futaba GY Pdf User Manuals. View online or download Futaba GY Instruction Manual. Nstruction, Anual • Read online or download PDF • Futaba GY User Manual. The chart below works for almost all helicopters but you should consult your helicopter manual if you are not sure. Note that I have seen.

Author: Akinojar Mihn
Country: Fiji
Language: English (Spanish)
Genre: Software
Published (Last): 18 January 2015
Pages: 400
PDF File Size: 5.35 Mb
ePub File Size: 3.74 Mb
ISBN: 712-8-70299-575-6
Downloads: 82667
Price: Free* [*Free Regsitration Required]
Uploader: Yozshuzil

That is the servo limit setting mode. Note that passwords are case-sensitive. Standard Rate mode Move the Gear switch down position 1.

Futaba GY Manuals

If you the tail wags in flight then decrease the gain. I was helping my buddy and he wanted me to hover it, so as soon as I did, the tail was super wobbly. Use the ‘clear’ button to set the values to zero. The gyro will repeat a ‘1 blink’. On this gyro it is easy to see the state it is in. Move the Gear switch down position 1. A high framerate setting on a low framerate servo will damage the servo in a minute.

Futaba GY520 Gyro

In the picture on the left you see I am not using them. The black wires of every plug all should be on the same side of the receiver. Also make sure that your plugs in the receiver have the correct polarity. Use an exacto knife to shave this off. The instructions state that you should set it up in HH mode if you are going to fly in HH mode-this is incorrect. I helped him some but gy5200 downloaded the GY manual and went through setup that way. It will be connected later.

  LEYDEN PAPYRUS PDF

On the small helicopters a gain of around 50 is normal. For the large and class helis use the two thick pads with the metal plate in between. manusl

In the picture, Aux2 is set to INH but this does not matter for this gyro setup. It is great they did this so you do not get mixed up.

The next second it will blink fast. Make sure you pay attention to the polarity of the receiver gu520. When you move the rudder stick to the right, it will move the trailing edge of the tail blades to the right side of the helicopter. Use a real email address or you will not be granted access to the site. The light will change to a violet color.

Also note that I added a slight bend to the front section of the tail control rod so that the link is at the same height as the ball on the servo arm. If the gyro is set for the wrong direction the helicopter will spin extremely fast as soon as it gets light on the skids.

Note the color of this light. The color at this point will indicate the mode the gyro is in. This would be very simple for Futaba to have done and would save some confusion. Once you set the travel for this side, quickly press and release the button on the gyro. Remove Advertisements Sponsored Links. Please click one of the Quick Reply icons in the posts above to activate Quick Reply.

Quickly press and release the gyro button to change the direction. Release the button and you will see the gyro light repeat a ‘1 blink’.

FUTABA GY Instruction Manual (Page 23 of 32)

This is going to vary for different helicopters and different brand servos. The first thing to do hy520 make the link slides as free as possible. It also depends on how the link connects to the servo. If not, hold the ,anual down to enter setup mode. Heading Hold Solid Blue: If none come close you can use the Rudder Sub-trim to adjust this but after you complete this step make sure you turn the heli off then back on so it will initialize at the new sub-trim position.

  ASKEP ATRESIA ANI PADA ANAK PDF

From the servo limit function, hold the gyro button down for 2 seconds to get to the Flight Mode selection. Power up the radio and the receiver. Make sure you can get to the gy5220 on the gyro. Mnual adjust the length of the tail control rod so that with the front link connected to the servo, the tail lever is 90 degrees to the tail control rod as seen in the middle picture on the left.

This will save the setting. With the main blades rotating clockwise as seen from above, the tail rotor should rotate counter-clockwise as viewed from the manyal side. This will set it up for the next step. You should make the decision based on what your flying style is.

When you power up the gyro for the first time you should have the tail servo disconnected. You can set this to what you need.