BLOG

MY PERSONAL JOURNEY

CD4052BE DATASHEET PDF

CDBE datasheet, CDBE pdf, CDBE data sheet, datasheet, data sheet, pdf, Texas Instruments, CMOS Differential 4-Channel Analog. CDBE ti CDB, CMOS Differential 4-Channel Analog Multiplexer/ demultiplexer With Logic-level Conversion Data sheet acquired from Harris. CDBE from TEXAS INSTRUMENTS >> Specification: Analog Multiplexer /Demultiplexer IC, Dual, Technical Datasheet: CDBE Datasheet.

Author: Mazugrel Tok
Country: Great Britain
Language: English (Spanish)
Genre: Medical
Published (Last): 19 May 2018
Pages: 257
PDF File Size: 17.15 Mb
ePub File Size: 19.92 Mb
ISBN: 850-9-28177-196-6
Downloads: 39264
Price: Free* [*Free Regsitration Required]
Uploader: Tukus

Sign up using Email and Password.

I reviewed another post that references the CD here, but it didn’t discuss the specific issues I was having. It is as if the multiplexer isn’t switching between x0, x1, x2 or x3. I started off with both A and B grounded.

Did I hook up this CD Analog Multiplexer correctly? – Electrical Engineering Stack Exchange

Post Your Answer Discard By clicking “Post Your Answer”, you acknowledge that you have read our updated terms of serviceprivacy policy and cookie policyand that your continued use of the website is subject to these policies.

I have hooked up the following circuit just to test the analog switching capability:. The analog MUX isn’t equivalent to a short. Why is there a voltage difference? Please let me know if something about this seems incorrect or is I just flat out misinterpreted the use of this chip.

  HIMNARIO APOSTOLICO PDF

If you need to switch the circuit with only 5v logic you can use an NPN transistor for each input, with a resistor on each collector pulled up to the Vdd level.

Post as a guest Name. That is actually where I would expect it to be. For dataeheet, it shows that with Vdd at 10v you need at least 7v for a high.

View cd4052be datasheet:

Your input logic to A,B should use the V1 voltage 12v for a high, not 5v. Also see the switching limitations listed datassheet jms. The R2, R3 and R4 all read 0v.

Home Questions Tags Users Unanswered. So at 12v Vdd you may need about a 9v minimum.

CDBE Datasheet(PDF) – Harris Corporation

Dave Guenther 1 While R1 reads 0. Email Required, but never cx4052be. This resistance adds to the 1 k external resistance and causes the voltage drop you saw. By using our site, you acknowledge that you have read and understand our Cookie PolicyPrivacy Policyand our Terms of Service. The control signals will be inverted from the base input to the collector output connection.

There are two things happening that don’t make sense to me when I test this same circuit:. Upon reading the data sheet this chip seems straight forward, but I’m having the hardest time hooking up the CD It seems like it should just be similar to an open wire between the two.

  IRYDOLOGIA W PRAKTYCE PDF

Datasehet up using Facebook.

CD4052BE Datasheet

It never occurred to me that logic high might be relative to Vdd. By clicking “Post Your Answer”, you acknowledge that you have read our updated terms of serviceprivacy policy and cookie policyand that your continued use of the website is subject to these datashwet.

I dont know why, maybe it fried? Here is a link to the datasheet. Sign up or log in Sign up using Google.

Nedd 4, 6 I have hooked up the following circuit just to test the analog switching capability: There are two things happening that don’t make sense to me when I test this same circuit: The DMM measurement reads the value 0. It is most likely implemented with pairs of back to back MOSFETs as the switches, and they have a significant on resistance of ohms or more.

Then send 5v signals into the base of each transistor with a series base resistorand the emitter is connected to GND.