Find great deals for Buderus RC35 Solar Card Room Controller Logamatic EMS. Shop with confidence on eBay!. View and Download Buderus RC35 instructions manual online. Room controller Logamatic EMS. RC35 Recording Equipment pdf manual download. View and Download Buderus RC35 operating instructions manual online. Room controller. RC35 Thermostat pdf manual download.

Author: Majora Nikosho
Country: Iran
Language: English (Spanish)
Genre: Automotive
Published (Last): 10 May 2010
Pages: 352
PDF File Size: 2.88 Mb
ePub File Size: 20.74 Mb
ISBN: 654-2-50319-202-7
Downloads: 11791
Price: Free* [*Free Regsitration Required]
Uploader: Grorg

Basic operation Basic operation 4.

Buderus RC35 Solar Card Room Controller Logamatic EMS

After some try and error, I have found that, for the RC35 Room Controller, values 39 and 7 for activation and deactivation work better. Yes, I wish a 24 month function guarantee by return of my defective article! Page of 60 Go. The selected program, custom 1 or custom 2, is used from now on for that heating zone.


The hours are saved. Heating zones with mixing valve, i. Page 9 In the case of large heating systems with multiple heating zones, note the following: Y our specialists for refurbished controls and more. The room temperature is set as described below. The Huderus next to lights up. All the existing addresses are queried once in a while by the bus master. If no selection is possible or if you select RC35 heating zones, you will be setting the same temperatures as described on page Press when you have finished making entries.

Operating Modes For Dhw However, the solar thermal system will cut out if either the collector array or the cylinder exceeds their maximum permissible temperatures collector protection function. Hold down the button and turn the dial to change the time for that switch point.


Page 15 – Changing the room temperature permanentl Press when you have finished making entries. It is only switched off if the heating system is switched off, such as for maintenance purposes.

B Answer the question Continue cancelling the vacation mode? Entering A Switching Point After that the switching point is saved.

Table of Contents Add to my manuals Add. Safety Instructions The heating system can freeze up in cold weather if it is not in operation: They all use the same datagram structure, changing only the message type as shown in buderks table:.

User menu A thermometer may indicate temperature fluctuations more slowly or rapidly than the RC However, it can also be requested. Principles of operation Principles of operation 4. We expressly point out that only approved staff buuderus permitted to work on electric- and gas-installations! For the RC35 heating circuits, you need to set the room temperature using Byte 11 contains additional information, out of the scope of this project. Note that if not otherwise indicated, all the values are transmitted using big endian order the most significant bytes are located at the lowest storage address.

I think it may be type 0x01 but not sure. Deleting A Switching Point The selected program, user defined1 or user defined2, is used from now on for that heating circuit. On the last Sunday in October the time changes from 3: The standard display then reappears. This is a status message containing some general information about the working conditions of the system.


If your heating system is equipped with rrc35 remote control e. Operation with the user menu — Individual heating circuits: Heating zone 4 Tab. This function is not available with boilers B If you want to stop the heating process: Leave the windows wide open for a few minutes rather than leaving them slightly open all the time.

To set the operating mode for ubderus heating zones: Selecting A Program If your heating system is equipped with a remote control e. Comments to this Manuals Your Name. The display will show a message to this effect. Please check our Heiz24 guarantess. B If the fault budfrus be reset the display continues to flashnotify your heating contractor.

The modified room temperatures are day: After that the switch point is saved.

There is no way to set this value with a write command or at least I have not been buxerus to achieve this so far. Deleting Budderus Point 1 or custom 2 or select not saved to cancel. Comments to this Manuals Your Name.

Operating instructions Logamatic EMS. Besides the default programs already defined in the controller, the user can create and edit two fully configurable programs with 42 switching points each per Heating Circuit.

The room temperature is set as described below.