Datasheet search engine for Electronic Components and Semiconductors. BAFM data sheet, alldatasheet, free, databook. BAFM parts, chips, ic. BAFM CD player for 4ch BTL driver Components datasheet pdf data sheet FREE from Datasheet (data sheet) search for integrated. Request Rohm BAFM: BAFMLSI online from Elcodis, view and download BAFM pdf datasheet, Rohm specifications. Page 4.

Author: Nell Tygolrajas
Country: France
Language: English (Spanish)
Genre: Personal Growth
Published (Last): 21 December 2007
Pages: 180
PDF File Size: 3.95 Mb
ePub File Size: 1.97 Mb
ISBN: 797-8-35592-757-2
Downloads: 78620
Price: Free* [*Free Regsitration Required]
Uploader: Jujin

Remove the four screws Torx 8 that hold the PWB [4].

DataSheet: BA5938FM

M Main Menu 1. Only qualified service personnel may remove the cover, or attempt to service this device due to possible eye injury. If necessary, it is now also possible to replace the sledgerack eatasheet that is hinged in the sledge assy. Make sure that, during datsheet, you are at the same potential as the mass of the set by a wristband with resistance.

Hold the sledge motor in its position by controlling the voltage on the motor continuously.

BAFP,BAFP,BAFP-YE2,BAFVM-TR,The Ic Datasheet,Price –

This subsystem recovers the data from the channel stream. PWB or ‘mono board’. Spindle Motor Test Loader fan, clamp, and tray assy. Therefore, during an access, the servo dafasheet to control as well the actuator as the sled. The motor, fan, and servo drivers use the 12 V. It EN 42 9. To achieve this, it is important that the sledge motor can rotate as daatsheet as possible. Nuclei Error Codes 5. Alignments No alignments necessary 9.


This action is signalised by the internal engine controller and reported to the application. The writing clock as obtained from this groove is very accurate.

The signal levels specification in this document are defined as follows: Consignment and warehousing available. The analogue front-end input converts the HF input to the digital domain via an xatasheet ADC, preceded by an AGC circuit to obtain the optimum performance from the converter.

In power ‘off’, the module does not respond to any communication or signal. Remove the fan assy, by releasing the four side clamps [1] while moving it upwards. Mesh the teeth of the sledge motor and sledge rack properly, during mounting of the sledgemotor assy. These are the analogue and digital power supplies and a local power supply for the laser driver function.

Use of controls or adjustments or performance of procedure other than those specified herein, may result in hazardous radiation exposure. This means that the player hangs. Figures below can deviate slightly from the actual situation, due to the different set executions. Driver Servo Board The application can react on this with a shock recovery procedure.

For lossless linking it is necessary to write any data block in the correct position with high accuracy within 1 micron. Above this magnetic ring are two hall sensors positioned 90 degrees apart. Firmware OPU flex Available ESD protection equipment: To reduce this time, the recorder has been equipped with Diagnostic and Service software DS. Contact us to buy or sell excess electronic component parts and inventory.


Basically, the OPC procedure tries to find out the optimum laser power to be used on a specific disc. For the flex foil on connectoryou first must remove the cable clamp [3].

If the engine detects unacceptable servo behaviour, the laser will go into low power mode to protect overwriting of neighbour tracks.

BA5938FM डेटा पत्रक PDF( Datasheet डाउनलोड )

PCS is implemented in the following way: Code number of PC interface cable: Parts list adepted in chapter 10 We are a franchised distributor of electronic components, as well as a sourcing and procurement agent for hard-to-find, obsolete, and allocated parts.

It dataaheet adjusts offsets, signal daatasheet, and loop gains AGCsto enlarge system robustness and to avoid expensive potentiometer adjustments in production. This will guarantee an optimal playability for all kind of discs. It consists of three phases: Flip the module degrees, so you can access the PWB.

Never try to align the DVD-Module! This signal is only used during recording, and therefore has no effect on the playback process. A normal DC motor is used, combined with hall sensors. Optical Pickup Unit 5. There is a solution ga5938fm this: Set the mains switch to the ‘on’ position keep the mains cord unplugged!