ASTM D/DM: Standard Test Methods for Tensile Testing of Aramid Yarns. ASTM D (D) determines the tensile testing of aramid yarns, cords twisted from such yarns, and fabrics woven from such cords. The yarn or cord may. How do you test yarn tensile strength for your application? Learn about ASTM D and how it compares to ASTM D in this basic test.
|Published (Last):||4 September 2013|
|PDF File Size:||10.26 Mb|
|ePub File Size:||10.31 Mb|
|Price:||Free* [*Free Regsitration Required]|
ASTM D7269 Tensile Testing of Aramid Yarns
ASTM D D determines the tensile testing of aramid yarns, cords twisted from such yarns, and fabrics woven from such cords. The yarn or cord may be wound on cones, tubes, bobbins, spools, or beams; may be woven into fabric; or may be in some other form.
Bluehill LE for Basic Testing. When needed to compare intrinsic strength characteristics of yarns or cords of different sizes or ast types of fiber, breaking tenacity is very useful because, for a given type of fiber, breaking force is approximately proportional to linear density.
They are designed with standard and optional features that increase testing efficiency and improve the testing experience for the operator. Email addresses can only contain letters, numbers and the following special characters: Testing conditions accordingly are specified precisely to obtain reproducible test results on a specific sample. Onsite Training At Your Facility.
ASTM D Testing Aramid Cords: The Proper Grip – Instron
The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. SI units is the technically correct name for the system of metric units known as the International System of Units. Have a question about conducting the test for this standard?
Forces up to 10 kN 2, lbf Low force tabletop systems Modular series of five frame options with adjustable test space D77269 testing option for tension, compression, bend, peel and much more.
Glossary of Materials Testing Terms. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. The values expressed in each system may not be exact equivalents; therefore, each system must be used independently of each other, without combining values in any way.
Other qstm with established test values may be used for this ast.
ASTM D – 07 Standard Test Methods for Tensile Testing of Aramid Yarns
This standard does not purport to address all of the safety concerns, if any, associated with its use. Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard.
The aramid cord and yarn grips did not exhibit symptoms of internal slippage.
Software for Series Systems. Historical Version s – view previous versions of standard.
ASTM D7269 Testing Aramid Cords: The Proper Grip
The yarn or cord may be wound on cones, tubes, bobbins, spools, or beams; may be woven into fabric; or may be in some other form. If a bias is found, either its cause must be found and corrected, or future test results must be adjusted in consideration of the known bias.
To check for slippage, we attached flags of tape to the ends of the cord and monitored them to make sure there was no relative movement of the flag with respect to the grip.
Subscribe to Our Newsletters. Users of previous versions of software such as Bluehill 2 and Bluehill 3 can easily upgrade to the newest version of Bluehill. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
Breaking toughness is work-to-break per unit mass. Link to Active This link will always route to the current Active version of the standard. Looking at the differences in the results between the regular and aramid cord and yarn grips, it seems that the cords gripped with the regular grips exhibited internal slippage in the jaw.
By means of our tensile testing expertise and modular product design, we will help find the solution that is right for you. Concrete, Asphalt and Rock. The gauge length of the specimen was set to mm. Due to this high strength nature, finding the correct grips for use in a tensile test can be quite challenging.