ASTM A ASME SA “Standard Specification for Nickel and Nickel-Base Alloy-Clad Steel. Plate”. “STANDARD SPECIFICATION FOR NICKEL AND. Buy ASTM A SPECIFICATION FOR NICKEL AND NICKEL-BASE ALLOY-CLAD STEEL PLATE from SAI Global. Designation: A − 12Standard Specification for Nickel and Nickel-Base Alloy- Clad Steel Plate1 This standard is issued unde.

Author: Kazim Bashicage
Country: Burkina Faso
Language: English (Spanish)
Genre: Marketing
Published (Last): 13 July 2004
Pages: 67
PDF File Size: 1.29 Mb
ePub File Size: 9.63 Mb
ISBN: 957-4-34650-396-1
Downloads: 33706
Price: Free* [*Free Regsitration Required]
Uploader: Arashigis

The steel shall be made by the open-hearth, electric furnace with separate degassing and refining optionalor basic-oxygen processes, or by secondary processes whereby steel made from these primary processes is remelted using, but not limited to electroslag remelting or vacuum arc remelting processes.

Ultrasonic Examination in accordance with Speci? The surface condition of the repaired area shall be restored to a condition similar to the rest of the cladding. A — 09 Standard Speci?

The base metal shall conform to the chemical requirements of the speci? Gage Length cladding and the base steel shall be machined so as to maintain the same ratio of clad metal to base steel as is maintained in the plate, except that the thickness of the clad material need not be reduced below 1?

This standard has been approved for use by agencies of the Department of Defense. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. Specify whether applicable to the cladding alloy, backing steel, or both see Section Permissible Variations Metric Equivalents in. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, are entirely their own responsibility.

This specification covers the standard for plate of a carbon steel a25 low-alloy steel base to which is integrally and continuously bonded on one or both sides a layer of nickel or nickel-base alloy. The reduced section shall have a gradual taper from the ends toward the center, with the ends 0. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and a2655.


Your comments will receive careful consideration at a meeting of the responsible technical committee, which you may attend. Reports shall include the results of ultrasonic inspection when Supplementary Requirement S12 is speci? The sides of the bend test specimen used for bond strength determination may have the corners rounded to a radius not over 1?

For purposes of de? The properties thus determined shall meet all of the tensile test requirements for the base steel. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract xstm accurate, complete or up to date.

A26 Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. Last previous edition approved in as A — A list of standardized supplementary requirements for use at the option of the purchaser are included in Speci?

The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. All other tensile test requirements of the speci? Number of Tests and Retests 8. Other tests may be performed by agreement between the supplier and the purchaser. Workmanship Finish, and Appearance Link to Active This link will always route to the current Active version of the standard.

General Requirements for Delivery The base metal shall be carbon steel or low-alloy steel conforming to the specifications for steels for either pressure vessels or for general structural applications. Individual reprints single or multiple copies of this standard may be obtained by contacting ASTM at the above address or at phonefaxor service astm. Method of test and acceptance standard shall be as agreed upon between the purchaser and the manufacturer.

Greater separation shall be cause for rejection.

ASTM A GR 1 titanium alloy strip sheet plate

The tensile properties thus determined shall meet the base steel requirements. Several of those considered suitable for use with this speci? This abstract is a brief summary of the referenced standard. If the requirements of this speci? Such requirements may include, but are not limited to the following: If you feel that your comments have not received a fair hearing you should make your views known to the ASTM Committee on Standards, at the address shown below.


The shear test, when speci? Each specimen shall be in the? If wet chemical procedures are used, millings may be taken a2655 when the composite plate thickness is sufficient to permit obtaining millings without danger of contamination from the adjacent layer. The composite plate shall astn shear strength test, bond strength test, and tension test and shall conform to the aztm tensile awtm and yield strength.

Product and chemical analyses shall be performed on the cladding alloy and be accomplished by wet chemical or instrumental procedures. ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentioned in this standard.

The nickel or nickel-base alloy cladding metal shall conform to prescribed chemical composition. Your comments are invited either for revision of this standard or for additional standards and should be addressed to ASTM International Headquarters. Originally approved in Historical Version s – view previous versions of standard Translated Version s: Materials and Manufacture 5. Historical Version s – view previous versions of standard.

In reducing the thickness of the specimen, both the alloy 3 Metric Equivalents in.

ASTM A265 Clad Plate

NOTE 3—The dimension t is the thickness of the test specimen as provided for in the applicable material speci? A number in parentheses indicates the year of last reapproval.

NOTE 2—Punch marks for measuring elongation after fracture shall be made on the?