Does anyone have a copy ofthe CBRR service manual yet? there are a few bits of service information I would like to find out about my new. Service your Honda CBRR motorcycle with a Cyclepedia service manual. Get color photographs, wiring diagrams, specifications and step-by-step. File Name: Honda CBRR Service File Submitted: Today at PM Honda CBRR Service

Author: Aragrel Zumi
Country: Nepal
Language: English (Spanish)
Genre: Life
Published (Last): 25 September 2005
Pages: 480
PDF File Size: 15.48 Mb
ePub File Size: 13.16 Mb
ISBN: 926-6-17278-202-2
Downloads: 49416
Price: Free* [*Free Regsitration Required]
Uploader: Mikazshura

Options Quote message in reply? I used the same magnet rod to magnetize a screwdriver for putting the shim back into place; the magnet rod itself was just too strong. Worked like a charm. Good but this is the Owners Manual, not the service manual. There are two different types of screws; the long shouldered one goes at the front. So, I guess it was a combination of a number of sites.

It is not leaking though. I found this service manual a while back.

Then flex things a bit and pop the cover off; it has two rubber grommets holding it. Found this link today: Anyone got the real one? In hindsight, I learned that you only need to remove the upper side fairings and the gas tank cover. Please enter your desired user name, your email address and other required dervice in the form below. I don’t think I have the top one in place correctly. To reinstall, hold the rocker arm in place and push the rod back into position and put the cover back on.

Originally Posted by Rudipides View Post.


Service Manual – Honda CBRR Forum : Honda CBR Forums

The manual did provide the details required to depressurize and disconnect the gas line. Honda CBR Forums forums, you must first register.

Working with the shims is tricky; a magnet rod is an absolute necessity. Careful with the signal wires; they are color coded. I’ve seen that manual. I downloaded this Thai version and it was almost useless. User Tag List Page 1 of 2 1 2. The valve cover gasket is sealed to the head surface at two places and I had to break the sealant as there was just no way to get the gasket back into the groove in the cover while putting seervice all together.

CBRR Honda Online Motorcycle Service Manual – Cyclepedia

For one thing, the U. Remove the two top screws beside the gas tank at the front you can see them when sitting on the bike. I only removed the exhaust one and am assuming the intake one is the same. I didn’t redo the sealant as I need to take it all apart again once I get the correct shims.

The fairings are each held on by three screws; one down at the bottom on the inside, one on the side and one at the front accessed from the front. If you end up doing this, can you take a picture of the rubber covers and post them?

What information are you looking for in particular? In that thread just click and download the Adobe. Quote message in reply? Note that passwords are case-sensitive. Owners Manual in English.

Also, that manual doesn’t make it clear that to adjust the valves without removing the cams, rocker arm shaft removal is required For the best viewing experience please update your browser to Google Chrome. The only usable access is if you remove the gas tank, the rubber shields and disconnect and tie some cables out of the way.


This is all there is so far: Password Please enter a password for your user account. Remove Advertisements Sponsored Links.

2011 2012 2013 CBR250R Honda Online Motorcycle Service Manual

Share Share this chr250r on Digg Del. You must take off the cover at the front of the gas tank to gain access to the tank bolt up there. If you remove the cover, you can then thread a 10mm bolt into the end of the pivot rod and pull the rod out just enough to let the rocker slip back exposing the shims.

Page 1 of 2. It then pops out of the clips. I also found some blogs about the engine and learned that on the ‘clutch’ side of the engine there are two cover screws Allen socket head near the valve cover seam that give access to the pivot rods of the rocker arms. Does anyone have a copy ofthe CBRR service manual yet? Originally Posted by pgkool Sevice Post. It seems to be a little different from the U. It is in English too!